How does the ultrasonic humidification system benefits experiment compared to traditional humidifiers?

The ultrasonic humidification system produces a very fine mist using ultrasonic vibrations rather than heat. This method helps maintain a stable humidity level without raising the temperature inside the chamber, which is crucial for experiments involving heat-sensitive samples such as biological cultures or pharmaceuticals. Traditional humidifiers often rely on boiling water or evaporation, which can cause unwanted temperature fluctuations and uneven humidity distribution. By using ultrasonic technology, the incubator ensures a more precise and consistent humidity environment, leading to better experimental accuracy and reproducibility.

Can the samples be observed without disturbing the controlled environment?

Yes, our Constant Temperature and Humidity Incubator is designed with a magnetic-sealed outer door that includes a clear observation window. This feature allows users to visually check on their samples at any time without opening the door. Opening the door can cause rapid changes in temperature and humidity inside the chamber, which might disrupt sensitive experiments. The observation window minimizes this risk, maintaining the internal environment's stability and reducing the chances of contamination or experimental errors caused by sudden environmental changes.

What are the important placement and safety precautions for the incubator?

The incubator must be properly grounded and placed in a shaded, cool, and well-ventilated area. It should maintain a minimum distance of 10 cm from walls to allow effective heat dissipation. During transportation, handle the device carefully and avoid tilting it more than 45 degrees from the horizontal plane to prevent damage.

How do I maintain the incubator when operating at low temperatures?

When using Labtron’s Constant Temperature and Humidity Incubator at low temperatures, it is important to regularly drain accumulated water from the drainage tray at the bottom to prevent condensation on the inner walls. This helps maintain stable humidity and prevents potential damage from excess moisture.

What should I do if the incubator suddenly stops working or experiences temperature control failure?

If operational issues occur, immediately disconnect the power. Check the fuse box located at the rear of the incubator for any blown fuses and replace them. If the problem persists, inspect related components such as the electric heating tube, axial fan, or circuit control board for faults.

Constant Temperature And Humidity Incubator LTHI-A10

Name: Constant Temperature And Humidity Incubator LTHI-A10
Brand: Labtron
SKU: LTHI-A10
Rating: 4.9 (969 reviews)

Constant Temperature and Humidity Incubator LTHI-A10 has a volume of 50 L and features a temperature control range of 0 to 80℃. It also features a humidity control range of 50 to 95% RH and uses ultrasonic humidification process. The incubator has an advanced microcomputer-based PID temperature controller that displays both set and actual values. Its internal chamber is made of corrosion-resistant mirror stainless steel and the outer body is treated with electrostatic high-temperature plastic spraying. Our incubator offers water quality analysis and BOD testing, and breeding experiments.

Request Quote

Volume	50 L
Temperature Control Range	0 to 80℃
Temperature Fluctuation	± 0.5℃
Temperature Resolution	0.1℃
Temperature Control Accuracy	±1℃
Humidity Control Range	50 to 95% RH
Humidity Fluctuation	± 5 to 8% RH
Display	LCD
Timer Range	0 to 9999 minutes or hours
Programmable Temperature Stages	30 stages, Up to 99 steps per cycle
Inner Tank Dimension	350 × 350 × 400 mm
Dimensions	450 × 540 × 1000 mm
Packing Dimension	520 × 600 × 1200 mm
Net Weight	50 kg
Gross Weight	60 kg

Over-temperature tracking alarm system
Multi-layer partition racks and pull-out partitions
All-round three-dimensional heating
Temperature correction function
Fan-forced convection circulation with air ducts
Magnetic-sealed outer door
Observation window on door
Four movable double-wheel casters

Our Constant Temperature and Humidity Incubator LTHI-A10 is ideal for suitable for scientific research, colleges and universities, and production departments such as environmental protection, health and epidemic prevention, drug testing, agriculture and livestock, and aquatic products.

Shelf × 1 piece

Power Cord × 1 piece

Humidifier × 1 set

Download catalog for
Constant Temperature And Humidity Incubator LTHI-A10 Catalog

Available Range :

Models of Constant Temperature and Humidity Incubator

Labtron’s Constant Temperature and Humidity Incubators are designed to provide a stable, controlled environment with accurate regulation of both temperature and humidity. Most of our incubators feature advanced microcomputer-based PID controllers and ultrasonic humidification technology. Their corrosion-resistant stainless-steel interiors and robust outer casings offer durability and ease of maintenance. Our incubators are ideal for a wide range of applications, including biological research, pharmaceutical testing, environmental studies, and quality control in agricultural and industrial processes.

Constant Temperature And Humidity Incubator LTHI-D12

Type : Constant Temperature and Humidity Incubator
Volume : 400 L
Temperature Range without Humidifying : 0 to 60°C
Temperature Range with Humidifying : 10 to 60°C

Compare Remove

Constant Temperature And Humidity Incubator LTHI-C15

Volume : 1600 L
Temperature Range without Humidifying : 0 to 85°C
Temperature Range with Humidifying : 10 to 60°C
Temperature Resolution : 0.1°C

Compare Remove

Constant Temperature And Humidity Incubator LTHI-B13

Volume : 600 L
Temperature Range without Humidifying : 0 to 70°C
Temperature Range with Humidifying : 10 to 60°C
Temperature Resolution : 0.1°C

Compare Remove

Constant Temperature And Humidity Incubator LTHI-B14

Volume : 800 L
Temperature Range without Humidifying : 0 to 70°C
Temperature Range with Humidifying : 10 to 60°C
Temperature Resolution : 0.1°C

Compare Remove

Constant Temperature And Humidity Incubator LTHI-C13

Volume : 800 L
Temperature Range without Humidifying : 0 to 85°C
Temperature Range with Humidifying : 10 to 60°C
Temperature Resolution : 0.1°C

Compare Remove

Constant Temperature And Humidity Incubator LTHI-D11

Type : Constant Temperature and Humidity Incubator
Volume : 250 L
Temperature Range without Humidifying : 0 to 60°C
Temperature Range with Humidifying : 10 to 60°C

Compare Remove

Constant Temperature And Humidity Incubator LTHI-E11

Volume : 375L
Temperature Range : 0 to 65℃
Display Resolution : 0.1℃
Operating Temperature : 5 to 40℃

Compare Remove

Constant Temperature And Humidity Incubator LTHI-C16

Capacity : 150 L
Temperature Range without Humidification : -10 to 85°C
Temperature Range with Humidification : 10 to 60°C
Temperature Resolution : 0.1°C

Compare Remove

Constant Temperature And Humidity Incubator LTHI-A10 FAQ's

The ultrasonic humidification system produces a very fine mist using ultrasonic vibrations rather than heat. This method helps maintain a stable humidity level without raising the temperature inside the chamber, which is crucial for experiments involving heat-sensitive samples such as biological cultures or pharmaceuticals. Traditional humidifiers often rely on boiling water or evaporation, which can cause unwanted temperature fluctuations and uneven humidity distribution. By using ultrasonic technology, the incubator ensures a more precise and consistent humidity environment, leading to better experimental accuracy and reproducibility.
Yes, our Constant Temperature and Humidity Incubator is designed with a magnetic-sealed outer door that includes a clear observation window. This feature allows users to visually check on their samples at any time without opening the door. Opening the door can cause rapid changes in temperature and humidity inside the chamber, which might disrupt sensitive experiments. The observation window minimizes this risk, maintaining the internal environment's stability and reducing the chances of contamination or experimental errors caused by sudden environmental changes.
The incubator must be properly grounded and placed in a shaded, cool, and well-ventilated area. It should maintain a minimum distance of 10 cm from walls to allow effective heat dissipation. During transportation, handle the device carefully and avoid tilting it more than 45 degrees from the horizontal plane to prevent damage.
When using Labtron’s Constant Temperature and Humidity Incubator at low temperatures, it is important to regularly drain accumulated water from the drainage tray at the bottom to prevent condensation on the inner walls. This helps maintain stable humidity and prevents potential damage from excess moisture.
If operational issues occur, immediately disconnect the power. Check the fuse box located at the rear of the incubator for any blown fuses and replace them. If the problem persists, inspect related components such as the electric heating tube, axial fan, or circuit control board for faults.